威尼斯89168澳门官方-威尼斯现场手机版

联系大家
    插件电感_大电流电感
热门搜索
点击排行
推荐电感
推荐阅读
推荐电感
推荐电感
猜猜你喜欢的
行业常识 您所在的位置: 电感 > 行业常识

亮度控制小灯电路

来源:    编辑:    发布时间:2014-12-25 16:00:49    浏览量:

亮度控制小灯电路--Brightness Control for small Lamps

Switching operated 1.5V bulbs
Portable unit, 3V battery supply
Parts:

P1________________470K Linear Potentiometer

R1_________________10K 1/4W Resistor
R2_________________47K 1/4W Resistor (See电感生产厂家 Notes)
R3__________________1K5 1/4W Resistor

C1_________________22nF 63V Polyester Cap工字电感acitor
C2________________100΅F 25V Electrolytic Capacitor

D1,D2___________1N4148 75V 150mA Diodes

IC1_______________7555 or TS555CN CMos Timer IC

Q1___________模压电感____BD681 100V 4A NPN Darlington Transistor

LP1_______________1.5V 200mA Bulb (See Notes)

SW1_______________SPST Switch

B1__________________3V (Two 1.5V AA or AAA cells in series, etc.)

Circuit operation: led

This device was designed on request, to control the light intensity of four filament lamps (i.e. a ring illuminator) for close-up pictures with a digital camera, powered by two AA or AAA batteries. Obviously it can be used in other ways, at anyones will.
IC大功率电感贴片电感器1 generates a 150Hz squarewave having a variable duty-cycle. When the cursor of P1 is fully rotated towards D1, the output positive pulses appearing at pin 3 of IC1 are very narrow. Lamp LP1, driven by Q1, is off as the voltage across its leads is too low. When the cursor of P1 is rotated towards R2, the output pulses increase in width, reaching their maximum amplitude when the potentiometer is rotated fully clockwise. In this way the lamp reaches its full brightness.

Notes:

LP1 could be one or more 1.5V bulbs wired in paralle电感器图片l. Maximum total output current allowed is about 1A.

R2 limits the output voltage, measured across LP1 leads, to 1.5V. Its actual value is dependent on the total current drawn by the bulb(s) and should be set at full load in order to obtain about 1.5V across the bulb(s) leads when P1 is rotated fully clockwise.

低成本的多节串联锂离子电池充电电路文中所述的集成电路KA7500B是SAMSUNG企业出品的一颗专用的脉宽调制型开关电源集成控制器,它与TL494完全兼容并可互换。该电路方案如下图所示。下面对该电路的工作原理作一说明:图中所绘电路本质上是一个电

在做一个AC90-264V输入,输出5V4A的USB充电器电源在做一个AC90-264V输入,输出5V4A的USB充电器电源,求成熟的方案。效率无特别要求,一般即可。只要求体积小,因为装配空间有限。不要求过认证。板子尺寸43*45mm,层高连脚到零件顶部

ROG固态硬盘PCIe接口设计,华硕CES 2013展风采标签:CES 2013(34)华硕(646)硬盘(165)接口(361)PCIe(44) 在本届CES消费电子展上,大家有幸看到了华硕ROG家族新成员 采用PCI-E接口设计的华硕ROG固态硬盘。华硕

 
在线客服

威尼斯89168澳门官方|威尼斯现场手机版

XML 地图 | Sitemap 地图